ESP32-DevKitC Core Board Type-C ESP32-WROVER ESP32-WROOM-32D/U Development Board

Description: Store CategoriesStore CategoriesOtherESP32-DevKitC Core Board Type-C ESP32-WROVER ESP32-WROOM-32D/U Development Board DetailsFeatures 1.ESP32-DevKitC development board, the new version of the mainstream TYPE-C interface, the backplane can be equipped with ESP32 modules: ESP-WROOM-32,ESP-WROOM-32D,ESP-WROOM-32U, ESP32-WROVER.2.ESP32-DevKitC is an entry-level ESP32 development board with integrated ESP32 pins pinned out for easy connection and use. It can be used to evaluate the full range of ESP32 modules and chips, and can be easily plugged into a breadboard.3.ESP32-DevKitC is a small development board based on ESP32 modules, supporting Wi-Fi and Bluetooth functions. The board has a rich set of peripherals, so users can easily realize product development.4.The on-board LDOs are led out to supply power for external components.ESP32-DevKitC groups different peripheral interfaces to help users get started with product development easily.5. The ESP32-DevKitC has excellent RF performance, allowing users to design and develop applications without having to consider RF and antenna design. The basic system requirements are already included on the development board, so users only need to connect the USB cable for development. SpecificationESP32-DevKitC development board:ESP32 based moduleEN: Reset button.Boot: Download button. Press and hold the Boot key, and press the EN key at the same time (do not release the Boot key at this time) to enter the "Firmware Download" mode and download the firmware through the serial port.USB-to-UART Bridge: Single chip USB-UART bridge that provides up to 3 Mbps transfer rate.Interface: TYPE-C connector that can be used as a power supply for the board or as a communication interface between the PC and the ESP32-WROOM-32 module.Communication: 2.4 GHz Wi-Fi + BluetoothProcessor: high-performance Xtensa@32-bit LX6 dual-core processor with ultra-low power co-processor.Multiple peripherals: Optimal power performance, RF performance, stability, versatility and reliability for various application scenarios and power requirements.The board can be powered by one of the following three power supply options:TYPE-C connector power supply (default)5V/GND pin supply3V3/GND pin supplyDimension: 54.4*27.9mm Module Performance:ESP-WROOM-32DChip: ESP32-D0WDSPI: Flash 32 Mbit, 3.3 VCrystal: 40 MHzAntenna: On-board PCB antennaWi-Fi protocol: 802.11 b/g/n (802.11n at speeds up to 150 Mbps)A-MPDU and A-MSDU aggregation with 0.4 µs guard interval supportOperating channel center frequency range: 2412~2484 MHzBluetooth protocol: BT v4.2 BR/EDR and BT LE compliantRF: NZIF receiver with -97 dBm sensitivity; Class-1, Class-2 and Class-3 transmitters; AFHIntegrated crystal: 40 MHz crystalIntegrated SPI flash1: 4 MBOperating/Power Voltage: 3.0 V ~ 3.6 VAverage operating current: 80 mASupply current minimum: 500 mARecommended operating temperature range: -40 °C ~ +85 °C ESP-WROOM-32UChip: ESP32-D0WDSPI: Flash 32 Mbit, 3.3 VCrystal: 40 MHzAntenna: External antenna connector, need to be used with external antennaWi-Fi protocol: 802.11 b/g/n (802.11n, speed up to 150 Mbps)A-MPDU and A-MSDU aggregation with 0.4 µs guard interval supportOperating channel center frequency range: 2412~2484 MHzBluetooth protocol: BT v4.2 BR/EDR and BT LE compliantRF: NZIF receiver with -97 dBm sensitivity; Class-1, Class-2 and Class-3 transmitters; AFHIntegrated crystal: 40 MHz crystalIntegrated SPI flash1: 4 MBOperating/Power Voltage: 3.0 V ~ 3.6 VAverage operating current: 80 mASupply current minimum: 500 mARecommended operating temperature range: -40 °C ~ +85 °C ESP32-WROVERSupply Voltage: 2.3V ~ 3.6VFrequency: 2.4 GHz ~ 2.5 GHzMounting Type : SMTData Rate: 150MbpsProtocol: 802.11b/g/nStorage Capacity: 4MBWi-Fi Protocol: 802.11 b/g/n (802.11n with speed up to 150 Mbps)A-MPDU and A-MSDU aggregation with 0.4 µs protection interval supportOperating channel center frequency range: 2412 ~ 2484 MHzBluetooth protocol: Compliant with Bluetooth V4.2 BR/EDR and Low Power Bluetooth standardsRF: NZIF receiver with -97 dBm sensitivityClass-1, Class-2 and Class-3 transmitters; AFHModule interfaces: SD card, UART, SPI, SDIO, I2C, LED PWM, Motor PWM, I2S, IR, Pulse Counter, GPIO, Capacitive Touch Sensor, ADC, DAC, TWAI® (ISO 11898-1 protocol compliant, i.e. CAN specification 2.0)On-chip sensors: Hall sensorsIntegrated crystal: 40 MHz crystalIntegrated SPI flash: 4 MBIntegrated PSRAM: 8 MBOperating voltage/supply voltage: 2.3 V ~ 3.6 VOperating Current: Average: 80 mAMinimum supply current: 500 mARecommended operating temperature -40 °C ~ 85 °C List1 x Development Board Shipping PolicyPayment MethodReturns PolicyShipping Policy We only accept your Ebay Address,Please Make sure it's 100% right. The items you ordered will be shipped out in 1 business day by Hong Kong Air Mail when your payment is clear. The arrival time is 5-20 business days to United States usually.We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutralor negative feedback, so that we can satisfactorily address your concerns. Payment MethodThis is the description of Payment Method. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Returns PolicyThis is the description of Returns Policy. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Copyright©2017 DataCaciquesESP32-DevKitC Core Board Type-C ESP32-WROVER ESP32-WROOM-32D/U Development Board Item DescriptionFeatures1.ESP32-DevKitC development board, the new version of the mainstream TYPE-C interface, the backplane can be equipped with ESP32 modules: ESP-WROOM-32,ESP-WROOM-32D,ESP-WROOM-32U, ESP32-WROVER.2.ESP32-DevKitC is an entry-level ESP32 development board with integrated ESP32 pins pinned out for easy connection and use. It can be used to evaluate the full range of ESP32 modules and chips, and can be easily plugged into a breadboard.3.ESP32-DevKitC is a small development board based on ESP32 modules, supporting Wi-Fi and Bluetooth functions. The board has a rich set of peripherals, so users can easily realize product development.4.The on-board LDOs are led out to supply power for external components.ESP32-DevKitC groups different peripheral interfaces to help users get started with product development easily.5. The ESP32-DevKitC has excellent RF performance, allowing users to design and develop applications without having to consider RF and antenna design. The basic system requirements are already included on the development board, so users only need to connect the USB cable for development. SpecificationESP32-DevKitC development board:ESP32 based moduleEN: Reset button.Boot: Download button. Press and hold the Boot key, and press the EN key at the same time (do not release the Boot key at this time) to enter the "Firmware Download" mode and download the firmware through the serial port.USB-to-UART Bridge: Single chip USB-UART bridge that provides up to 3 Mbps transfer rate.Interface: TYPE-C connector that can be used as a power supply for the board or as a communication interface between the PC and the ESP32-WROOM-32 module.Communication: 2.4 GHz Wi-Fi + BluetoothProcessor: high-performance Xtensa@32-bit LX6 dual-core processor with ultra-low power co-processor.Multiple peripherals: Optimal power performance, RF performance, stability, versatility and reliability for various application scenarios and power requirements.The board can be powered by one of the following three power supply options:TYPE-C connector power supply (default)5V/GND pin supply3V3/GND pin supplyDimension: 54.4*27.9mm Module Performance:ESP-WROOM-32DChip: ESP32-D0WDSPI: Flash 32 Mbit, 3.3 VCrystal: 40 MHzAntenna: On-board PCB antennaWi-Fi protocol: 802.11 b/g/n (802.11n at speeds up to 150 Mbps)A-MPDU and A-MSDU aggregation with 0.4 µs guard interval supportOperating channel center frequency range: 2412~2484 MHzBluetooth protocol: BT v4.2 BR/EDR and BT LE compliantRF: NZIF receiver with -97 dBm sensitivity; Class-1, Class-2 and Class-3 transmitters; AFHIntegrated crystal: 40 MHz crystalIntegrated SPI flash1: 4 MBOperating/Power Voltage: 3.0 V ~ 3.6 VAverage operating current: 80 mASupply current minimum: 500 mARecommended operating temperature range: -40 °C ~ +85 °C ESP-WROOM-32UChip: ESP32-D0WDSPI: Flash 32 Mbit, 3.3 VCrystal: 40 MHzAntenna: External antenna connector, need to be used with external antennaWi-Fi protocol: 802.11 b/g/n (802.11n, speed up to 150 Mbps)A-MPDU and A-MSDU aggregation with 0.4 µs guard interval supportOperating channel center frequency range: 2412~2484 MHzBluetooth protocol: BT v4.2 BR/EDR and BT LE compliantRF: NZIF receiver with -97 dBm sensitivity; Class-1, Class-2 and Class-3 transmitters; AFHIntegrated crystal: 40 MHz crystalIntegrated SPI flash1: 4 MBOperating/Power Voltage: 3.0 V ~ 3.6 VAverage operating current: 80 mASupply current minimum: 500 mARecommended operating temperature range: -40 °C ~ +85 °C ESP32-WROVERSupply Voltage: 2.3V ~ 3.6VFrequency: 2.4 GHz ~ 2.5 GHzMounting Type : SMTData Rate: 150MbpsProtocol: 802.11b/g/nStorage Capacity: 4MBWi-Fi Protocol: 802.11 b/g/n (802.11n with speed up to 150 Mbps)A-MPDU and A-MSDU aggregation with 0.4 µs protection interval supportOperating channel center frequency range: 2412 ~ 2484 MHzBluetooth protocol: Compliant with Bluetooth V4.2 BR/EDR and Low Power Bluetooth standardsRF: NZIF receiver with -97 dBm sensitivityClass-1, Class-2 and Class-3 transmitters; AFHModule interfaces: SD card, UART, SPI, SDIO, I2C, LED PWM, Motor PWM, I2S, IR, Pulse Counter, GPIO, Capacitive Touch Sensor, ADC, DAC, TWAI® (ISO 11898-1 protocol compliant, i.e. CAN specification 2.0)On-chip sensors: Hall sensorsIntegrated crystal: 40 MHz crystalIntegrated SPI flash: 4 MBIntegrated PSRAM: 8 MBOperating voltage/supply voltage: 2.3 V ~ 3.6 VOperating Current: Average: 80 mAMinimum supply current: 500 mARecommended operating temperature -40 °C ~ 85 °C List1 x Development Board Payment1.We only accept payment from PayPal. 2.Please make sure your eBay address is correct before you pay. 3.All payment Should be Completed within 7 days, or an unpaid disputed will be opened as payment none receive. 4.If you do not want to pay for the order please contact us via eBay message, we will help your cancel the transaction. Shipping 1. We only ship to confirmed ebay addresses. 2. Economy Shipping, don't have tracking number. Standard Shipping, with tracking number. Express (Expedited) Shipping, with tracking number. If you need a tracking number, you could choose Standard Shipping. 3. Economy shipping needs 2-5 weeks to arrive mostly. In rare case, it can take up to 6-8 weeks. It depends on your location and local postal service, as well as the weather condition along the shipping. 4. If you need a faster delivery time, you could choose Express (Expedited) Shipping. Return 1. We offer 60 day money back or replacement guarantee. In addition, it allows customers to return new and unused products in their original factory condition for any reason within 60 days from the date of purchase. 2. Although we test each item and they are packed professionally, few item(less than 0.1%) might be damaged during the shipping. Please feel free to contact us within 7 days after you receive your package about replacement. 3. If you don't receive items over 35days ,please make sure to contact us before leaving any neutral or negative feedback.We'll try our best to help you solve the problem. If we authorized the return, customers will get an email with instructions for returning the item. Email will be replied within 24 hours on Chinese business hours. The sole and exclusive maximum liability to lifesteward arising from any product sold on lifesteward ebay account shall be the price of the product ordered. Feedback 1. Customer satisfaction is our top goal. We believe our items are so outstanding. All products are quality checked. They are new and in good condition when shipped to our customers. We are convinced you will be happy with your Purchase. 2. If product is defective or damage upon arrival, or wrong product shipped, please contact us immediately. Returns accepted within 14 days of delivery date and item must be in original new condition, not worn or altered in any way with attached tags & wrap. Otherwise deal is final. Return shipping must be paid by buyer. 3. We appreciate your Postive Feedback, and will do the same in return. DO NOT leave negative feedback without first communication with us. Please allow max 2 business days for us to response.On Oct 22, 2024 at 19:30:49 PDT, seller added the following information:

Price: 11.69 USD

Location: Jamaica, New York

End Time: 2024-11-23T03:26:12.000Z

Shipping Cost: 0 USD